Hammer type surface resistance tester Seller, Supplier, Exporter, Manufacturer, Factory

Hammer type surface resistance tester
Shenzhen Maxsharer Import & Export Co.,Ltd
[ view Shenzhen Maxsharer Import & Export Co.,Ltd company information and other listings ]

Hammer type surface resistance tester

This Tester is designed basing on testing regulations of EOS/ESD, CECC, ASTM & UL, and used
to detect impedance or resistance on surfaces of all conductive, ESD and electrostatic dissipative
substances. Simple operation, good quality and High reliability, which also could measure
relative humidity & temperature of the target.
• Test of impedance, temperature and humidity, conformity to criterion of ESD, S4.1, S7.1, &
S11.11
• Resistance test range 10^3- 10^12 ohm, suitable for all sorts of material.
• Standard voltage- 10v/100v, suitable for standard working table and ground floor.
• Packing case offered used to give meter protection against accidental damage.
• Little weight, just 150z(425g) , so
• Automatical power-cut function to prolong battery life.
• Clear to zero automatically to ensure accuracy
• Parallel electrode, 5 pounds detector and inside impedance detector configured are conform to
criterion of ASTM, EOS & CECC.
• NIST certified, ISO9000 ensurance.
• 9v DC, Nichle Cadmium charge cell or AC Transformer for all purpose. overseas.
OPERATION INSTRUCTION
1. Surface Resistivity—Parallel Probe Resistivity Method
The Method is very swift for resistance testing of average materials, which conforms to criterion
of EOS/ESD-S11.11-1993. Also this suits to the test of multi-layers material, meanwhile
temperature and humidity data in report is required.
A. Place the meter on testing surface.
B. Turn to right voltage(10v or 100v)
C. Press test button with pressure of approximate 5 pounds, here LCD screen would display final
datas-------test process would last for 15 seconds.
▲ surface impedance : ohm
▲ temperature : Celsius Degree
▲ relative humidity : percentage
During every test, the meter would display datas continuously when pressing the button, and in 45
seconds after button released, data shown is the last one.
2. Surface Resistance Measurement (RTT)
This method(conforms to EOS/ESD-S4.1) is used to test resistance between two points of ground
touch, and the result is relavent to specific distance of two 5pounds detector and the condition of
testing target. So, correct tesing way should be selected, and every testing condition required
should be the same.
A. Insert wire plug into two holes of 3.5mm, also connect banana plug with two 5pounds
detector.
B. Place two detectors on target surface as required.
C. Select correct voltage (10v or 100v)
D. Press the button till voltage selected is shown on screen, keep pressing till all
datas(resistance, relative humidity and temperature) display.
3. Surface-To-Ground Resistance Measurement (RTG)
This method is used to measure surface resistance of target from one point of its surface to another
point which touches ground, also conforms to test criterion of EOS/ESD S4.1.
A. Insert each end of two cords separately into two holes of DIA 3.5mm, and then connect one
cord with clip, the other with 5pounds detector.
B. Link the clip to ground touch point as required, and then place detector on testing surface.
C. Press the button till all datas is displayed, result conforms to criterion of EIA, EOS/ESD ,
ANSI, IEC-93, CECC and ASTM. To ensure accuracy of test when testing material of high
impedance, crossover of two cords and hand-touch of any relative testing substances are not
allowed.

Category :	Laboratory Equipment
Related Searches :	hammer , hammers , resistance tester , resistance testers , surface , surface resistance tester
Country Of Origin :	China
Listing Type :	Sell
Contact :	Rago Chen
Address :	Room 2208, Baotong Building, Baomin 1st,Baoan shenzhen, Guangdong, 518133 China
Telephone :	[86] (755) 33853681
Fax :	[86] (755) 33853685

Hammer type surface resistance tester

hammer

hammers

resistance tester

resistance testers

surface

surface resistance tester