Sell 16E1-Eth interface converter

16E1-Eth interface converter You May Also Be Interested In: e1 to ethernet ethernet networks ethernet switches interface converter optical ethernet
/8/16E1 to 4*Ethernet Converter
(GFP/VCAT/LCAS supported)


Ethernet over 16E1 Converter allows the user to send Ethernet data, between two points, over E1 links. E1 Interfaces are 120 Ohms (75 Ohms is optional) . Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm/1310nm/1550nm single mode optical fiber interfaces.

The equipment be always installed and used in pairs, with one terminal being installed at either end of the E1 link.

The Ethernet over 16E1 Converter is an Ethernet extension device utilizing TDM telecom infrastructure (the telecom network of E1s, or of PDH, SDH and E1/E3/SDH microwave etc. carrying E1s) . It converts the Ethernet data into E1 frame format for transmission over the existing TDM (E1) links and then re-converts the E1 back into Ethernet data the far-end terminal, to BRIDGE two Ethernet LANs over the existing E1-based telecom network. The device can effectively utilize the existing TDM network to transport Ethernet data with low investment.


Provides 16 E1 interfaces
Provides 4 Ethernet 10/100Mbps (Elecrical) ports for each converter
The maximum transmission rate of Ethernet data over E1 links is 32.768Mbit/s
Optionally provides 3 Ethernet 10/100Mbps (Elecrical) ports and 1 Ethernet (Optical) port for each converter
E1 supports three working modes of transmission. Un-Framed/Transparent, Framed, CAS / PCM 30 format
Supports VCAT (virtual concatenation) and LCAS (link capacity adjustment scheme) protocol, and complies with ITU-T G.7042 specifications
Mapping to E1 complies with ITU-T G.7043 and G.8040 specifications
Supports differential delay of up to 120ms on E1 links
Complies with IEEE 802.3 specifications
Support VLAN tagging as per 802.1Q
Supports X.86, LAPS and HDLC transmission protocols
Supports 100M full-duplex mode
Configurable frame length upto 1916 bytes (MTU size)
Supports GFP-F encapsulation complying with ITU-T G.7041
Provide smooth adjustment of bandwidth
Provides Loss of Frame alarms
Provides error frame statistic
Supports automatic removal and addition of E1 links
Available with MAC address list filtration, learning, and updating functions
A large external SDRAM buffering for handling data bursts
E1 Interfaces support errors count
Tolerant for drift of E1 signal of up to 512UI.
Error code correction and automatic protection and recovery of E1 channel.
Network management function. The main function of network management system is to fulfill the inquiry for local and remote devices and configuration management including inquiry of alarm status on E1 line, Ethernet working status, and loopback control etc.
Automatic ethernet negotiation function. Supports 10M/100M and working modes of both full-duplex and semi-duplex.
Transparently transmits ultra-long frames stipulated in IEEE 802.1Q, and supports Ethernet switches with VLAN function.
Supports two synchronization clock modes, Internal Clock and Network Clock (Loop-Timed Clock)
Imbedded, dynamic Ethernet MAC address list (5000 addresses) , and filter function for local data frames

Typical Application:

Bridging Ethernet LANs over existing TDM (E1) telecom network.
Extending Ethernet networks utilizing TDM (E1) landline based telecom infrastructure.
Interconnecting DSLAMs to Central Routers over PDH/SDH
Interconnecting IP based GSM base stations
Interconnecting WiMAX base stations
Using telecom network of E1s / PDH / SDH microwave etc. carrying E1s to transport Ethernet data.

In all cases the equipment be always installed and used in pairs, with one terminal being installed at either end of the network.
Brand Name
Supply Capacity
Model Number